WARNING: ! WARNING: This installation is not for the tuning novice! Use this system with EXTREME caution! If you are not well ve
Page 10 10-2860 B Series COP Instructions RevB 111117 The Coil Phasing sets the firing order of the coils and must match the Injector phasing. For
Page 11 10-2860 B Series COP Instructions RevB 111117 Series 1 EMS Coil Dwell Open the coil dwell template in AEM Pro by clicking on the ignit
Page 12 10-2860 B Series COP Instructions RevB 111117 ECU Trigger The Four Channel Coil Driver included in this kit requires a 5V logic level
Page 13 10-2860 B Series COP Instructions RevB 111117 Remove the four mounting screws on the bottom of the EMS enclosure. See Figure 17 below.
Page 14 10-2860 B Series COP Instructions RevB 111117 Remove the four screws and spacers that hold the two circuit boards together. The screws are
Page 15 10-2860 B Series COP Instructions RevB 111117 Separating the circuit boards requires some patience and caution. It works well to think of
Page 16 10-2860 B Series COP Instructions RevB 111117 Place the jumpers in the positions listed in Table 3. Only the jumpers listed belo
Page 17 10-2860 B Series COP Instructions RevB 111117 Once reassembled, install the EMS and reconnect the battery cables. Model specific EMS i
Page 18 10-2860 B Series COP Instructions RevB 111117 EMS Pin Locations Relevant pin locations for the 30-6040, 30-6050, and 30-6060 Series 2 EMS
Page 19 10-2860 B Series COP Instructions RevB 111117 CONNECTOR PINOUTS Pinouts for the EPM and B Series COP harness connectors are shown below.
Page 2 10-2860 B Series COP Instructions RevB 111117 KIT CONTENTS 1 x 35-2840 IGNITER W/ BRACKET 1 x 30-3255 HONDA EPM 4 x 30-2850 COIL 1
Page 20 10-2860 B Series COP Instructions RevB 111117 EPM Connector FACTORY TACHOMETER Setup Normally the distributor provides the input sign
Page 21 10-2860 B Series COP Instructions RevB 111117 SPECIFICATIONS 30-2860 B Series COP Ignition Type Inductive with Igniter Ignition Channels
Page 22 10-2860 B Series COP Instructions RevB 111117 WARRANTY 12 MONTH LIMITED WARRANTY Advanced Engine Management Inc. warrants to the consumer
Page 3 10-2860 B Series COP Instructions RevB 111117 Remove the retaining clip from the drive gear and remove the pin, drive gear, and shim. S
Page 4 10-2860 B Series COP Instructions RevB 111117 AEM Engine Position Module (EPM) Apply a small amount of clean engine oil to the shaft o
Page 5 10-2860 B Series COP Instructions RevB 111117 Coils With the factory plug wires removed, apply a small amount of dielectric grease insi
Page 6 10-2860 B Series COP Instructions RevB 111117 B Series COP Harness Lay the B Series COP harness over the cylinder head and connect the coil
Page 7 10-2860 B Series COP Instructions RevB 111117 EPM Harness Connect the 4-pin connector on the EPM harness to the mating connector on the EPM
Page 8 10-2860 B Series COP Instructions RevB 111117 B Series COP Harness RED (IGN) – Connect to switched, fused (15 A or greater) 12 volts
Page 9 10-2860 B Series COP Instructions RevB 111117 Coil Firing In order for the EMS to fire each coil individually, the coils must be activa
Commentaires sur ces manuels