Aem 30-3432 Series 2 AEMnet Adapter Manuel d'utilisateur télécharger pdf

AEM Performance Electronics

2205 W 126

Street Unit A, Hawthorne, CA 90250

Phone: (310) 484-2322 Fax: (310) 484-0152

http://www.aemelectronics.com/

Instruction Part Number: 10-3430 Rev 1

 2011 AEM Performance Electronics, Inc.

Page 1

AEMnet

AEMnet is an open architecture software and hardware interface based on the CAN 2.0 specification,

which provides the ability for multiple AEMnet enabled devices to easily communicate with each other

through a single cable. The hardware connection is made through a Deutsch 4P DTM connector.

Devices connected to the AEMnet transmit data through this one connection. Once the AEMnet

adapter is installed, the Series 2 EMS will be able to send and receive data on the AEMnet.

Instructions for configuring the Series 2 EMS to output data are included in this manual. Instructions

on configuring the Series 2 EMS to receive data from other AEMnet enabled products are contained

in the individual product manuals. Upon completion of these instructions, the Series 2 EMS will be

configured to output data to an AQ1 Data Logger or other data receiving device.

The following AEM products are currently AEMnet enabled:

Series 2 Engine Management System

EMS-4 Universal Standalone Engine Management System

4-Channel Wideband UEGO Controller

AQ-1 Data Logger

Dyno Shaft On-Vehicle Dynamometer

Instruction Manual

P/N 30-3430, 30-3431, 30-3432, & 30-3435 AEMnet Adapter Harness

Installation for Series 2 EMS 30-6030, 30-6050, 30-6051, 30-6052, 30-

6053, 30-6060, 30-6310, 30-6311, & 30-6320

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Instruction Manual

AEM Performance Electronics 2205 W 126th Street Unit A, Hawthorne, CA 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 http://www.aemelectronics.com/

Page 2 - AEMnet CONNECTORS

Page 2 AEMnet CONNECTORS The AEMnet has four wires, two are for communication (white pin 1 and green pin 2) and two are for powering (red pi

Page 3

Page 3 REMOVE EXISTING WIRES FROM ECU PLUG(S) 1. Locate a small screwdriver (a precision 1.5mm wide flathead screwdriver is recommended) an

Page 4

Page 4 2. Next remove the pin from the plastic connector by lightly prying on the plastic tabs that secure the pin in the plastic connector

Page 5

Page 5 INSTALL AEMnet ADAPTER HARNESS 4. Table 2 below lists the corresponding CAN1L and CAN1H pin locations for each Series 2 EMS. CAN1

Page 6

Page 6 5. To install the harness into the ECU plug, align the CANL and CANH pins into the receptacle of the plug and push in until it click

Page 7 - CONFIGURING THE SERIES 2 EMS

Page 7 CONFIGURING THE SERIES 2 EMS The AEMnet data stream is compatible with version AEM25 01v23 firmware and later. To activate the AEMnet

Page 8 - WARRANTY

Page 8 WARRANTY 12 MONTH LIMITED WARRANTY Advanced Engine Management Inc. warrants to the consumer that all AEM High Performanc

Commentaires sur ces manuels

Pas de commentaire

Aem 30-3432 Series 2 AEMnet Adapter Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Aem 30-3432 Series 2 AEMnet Adapter. AEM 30-3432 Series 2 AEMnet Adapter User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Aem 30-3432 Series 2 AEMnet Adapter